產品資訊

 品極(PINTEK) 示波器 PS-608 

Model: PS-608
-- pintek ps-608
60MHzALT雙頻觸發
讀出示波器狀況V/DIVS/DIVMAGUNCAL、△V、△T1/T及測試值等
亦可兼60MHz計頻器使用
1mV/DIV靈敏度、10nS/DIV解析度
垂直及水平4條游標基準線更方便觀測及使用

 

pintek ps-608 規格表:

CRT:

Type :

Rectangular with integral graticule.

Display Area :

8 x 10 div ( 1 div = 1 cm )

Accelerating Voltage :

12kV.

Phosphor :

P31.

VERTICAL AMPLIFIERS ( CH 1 and CH 2 )

Sensitivity :

5 mV / div to 5 V / div ( X1 mode ).

1 mV / div to 1 V / div ( X5 mode ).

1-2-5 sequence, 10 step attenuator. Vernier control provides fully adjustable attenuation between steps.

Accuracy :

± 3 % ( X1 mode );± 5 % ( X5 mode ).

Input Resistance:

1 MΩ ± 2 %.

Input Capacitance:

25 pF ± 10 pF.

Frequency Response:

5 mV to 5 V / div ( CAL ):DC to 60 MHz (-3 dB).
1 mV / div (CAL):DC to 20 MHz (-3 dB).

Rise Time:

Approximately 5.8 ns.

Operaing Modes:

CH1:

CH 1, single trace.

CH2:

CH 2, single trace.

ALT:

Dual trace, alternating.

CHOP:

dual trace, chopped.

ADD:

algebraic sum of CH 1 + CH 2.

Polarity Reeversal (Invert):

CH 2 only.

Maximum Input Voltae:

400 V dc + ac peak.

Maximum Undistorted Amplitude:

DC-to-60 MHz:

4 divisions.

DC-to-40 MHz:

8 divisions.

HORIZONTAL AMPLIFIER( Input through channel 1 input )

X-Y mode:

switch selectable using X-Y switch.

CH 1:

X axis.

CH 2:

Y axis.

Sensitivity:

1mv/div to 5v/div

Accuuacy:

 

Y-Axis:

 ± 3%.

Y-Axis:

 ± 6%.

Input Impedance:

1MΩ ± 2% //25PF

Frequency Response:

DC to 1 MHz typical ( -3 dB ).

X-Y Phase Difference:

Approximately 3° at 50 kHz.

Maximum Input Voltage:

400v dc+ac pack

SWEEP SYSTEM

Sweep Speed:

0.1 μs/div to 0.5 s/div in 1-2-5 sequence, 21 steps.
Vernier control porvides fully adjustable sweep time between steps.

Accuracy:

± 3 %.

Sweep Magnification:

10X, ± 10%

Holdoff:

Continuously adjustable from NORM to 5 times normal.

TRIGGERING

Trigger Modes:

AUTO ( free run ) or NORM.

Trigger Source:

CH1, CH2, ALT, EXT, LINE.

Maximum External Trigger Voltage:

300 V dx + AC peak.

Trigger Coupling:

AUTO ( AC ):

30 Hz to 80 MHz.

TV-H ( AC ):

Used for triggering from horizontal sync pulses.

TV-V ( DC ):

Used for triggering from vertical sync pulses.

READOUT FUNCTION-Panel setting desplays

Vertical axis ( CH1, CH2 ) :

V/DIV,UNCAL, MAG ( Converted Value)

Horizontal axis :

S/DIV, UNCAL, MAG ( Converted Value)

-Cursor readout function

Voltage difference V :

to REF

Time difference T :

  to REF

Frequency diference 1/ T:

1/1 to REF 1

NOTE:

When the X-Y mode, V is changed to X and T to Y.

-Cursor measurement resolution :

1/25 DIV

-Effective cursor range from center graticule

Vertical :

within ± 3 DIV

Horizontal :

within ± 4 DIV

OTHER SPECIFICATIONS

Calibrating Voltage:

1 kHz ( nominal ) Positive Square Wave, 0.5 V p-p ( ± 3% )

Trace Rotage:

Electrical, front panel adjustable.

Power Requirements:

115/ 230 VAC ± 10%, 50/60Hz , approximately 60 W.

Dimensions:

324 x 132 x 398 mm ( 12.8 x 5.2 x 15.6" ).

Weight:

Approximately 8.5 kg ( 18.7 1bs ).

 

top       

Copyright 2005-2008 Fast Auto Electronic | Power by Manlink Network INC